Prestige R2Customer login

Prestige R2 and R2 Pro - How To Replace The Capping Station

Every step links to its own moment in the video, so you never hunt for the right part again.

  • 21 steps
  • 99 instructions
  • 1 video
  • Updated 2026-04-20

Prestige R2 Capping Station Replacement Guide

  1. 0:01Overview and When to Replace
  2. 0:33Step 1 – Power Down and Initial Positioning
  3. 1:01Step 2 – Remove Front and Side Panels
  4. 1:23Step 3 – Disconnect Tubes and Top Assembly
  5. 1:58Step 4 – Document and Remove L-Bracket and Cables
  6. 2:31Step 5 – Remove Wiper Blade and Lower Assembly
  7. 2:59Step 6 – Access Rear Cable Routing
  8. 3:59Step 7 – Remove Rear Panel and Release Cables
  9. 4:36Step 9 – Install New Capping Station
  10. 5:21Step 11 – Mount and Route Cables
  11. 6:09Step 12 – Initial Mechanical Alignment
  12. 7:29Step 13 – Adjust Capping Station Tilt
  13. 8:31Step 15 – Adjust Wiper Blade Height
  14. 9:42Step 16 – Save and Initialize
  15. 10:23Step 17 – Final Contact Verification
  16. 11:07Step 18 – Final Reassembly
Written steps 21

Overview and When to Replace

Watch this part0:01

What you need

  • Capping station no longer moves up to meet the print head
  • Grinding noises from the capping station
  • Poor sealing against the print head

Required Tools and Supplies

What you need

  • Phillips screwdriver
  • Allen wrench
  • Scissors
  • Gloves
  • Small zip ties
  • Replacement cable
  • New capping station

Step 1 – Power Down and Initial Positioning

Watch this part0:33
  1. Turn the printer completely off using the rear power switch.
  2. Ensure no media is loaded in the printer.
  3. Rotate the capping station knob counterclockwise to lower the capping station fully.
  4. Slide the printer carriage to the left.

Step 2 – Remove Front and Side Panels

Watch this part1:01
  1. Remove the five screws securing the front panel.
  2. Open the side door.
  3. Remove the two screws on the side panel.
  4. Remove the panel.
  5. Carefully remove the capping station cover.

Step 3 – Disconnect Tubes and Top Assembly

Watch this part1:23
  1. Remove the four screws securing the top capping station panel.
  2. Lift the panel slightly without pulling it fully out.
  3. Take note of the four ink tubes connected to the assembly.
  4. Label the tubes if needed.
  5. Remove all four tubes.

Step 4 – Document and Remove L-Bracket and Cables

Watch this part1:58
  1. Take a picture of the L-bracket orientation and screw height.
  2. Note the position of the two screws on the L-bracket.
  3. Locate the connected cable.
  4. Remove the cable by pulling on the white plastic connector only.

Step 5 – Remove Wiper Blade and Lower Assembly

Watch this part2:31
  1. Use an Allen wrench to remove the two bolts securing the assembly.
  2. Locate the wiper blade assembly.
  3. Remove the wiper blade carefully.
  4. Detach the drain tube connected to the wiper blade.
  5. Remove the additional two bolts securing the capping station base.

Step 6 – Access Rear Cable Routing

Watch this part2:59
  1. Open the two rear panels.
  2. Take pictures of cable routing and zip tie locations.
  3. Cut the four zip ties securing the capping station cables.
  4. Locate the two bottom-left cables and unplug both.
  5. Cut the two side zip ties to free the cables.

Step 7 – Remove Rear Panel and Release Cables

Watch this part3:59
  1. Move the waste tank to the side.
  2. Remove the eight screws securing the rear panel.
  3. Remove the panel.
  4. Locate and cut the two additional zip ties.
  5. Pull both cables completely out toward the capping station side.

Step 8 – Remove Old Capping Station

  1. Remove the entire capping station assembly from the printer.

Step 9 – Install New Capping Station

Watch this part4:36
  1. Position the new capping station in the same orientation as the old unit.
  2. Reorganize tubes to their original positions.
  3. Route the replacement cable toward the back of the printer.
  4. Connect the cable to the side of the capping station.

Step 10 – Secure and Align New Assembly

  1. Install the two Allen bolts loosely to allow adjustment.
  2. Secure the two bolts on the opposite side.
  3. Attach the top bracket assembly.
  4. Tighten the bracket with a screwdriver.
  5. Reinstall all tubes exactly as originally routed.

Step 11 – Mount and Route Cables

Watch this part5:21
  1. Place the capping station assembly into position.
  2. Secure it with the mounting screws.
  3. Route the first cable through the rear opening.
  4. Pull it through from the back and plug it into the correct port.
  5. Route and connect the second cable.
  6. Adjust the L-bracket and screws to match the reference photo.

Step 12 – Initial Mechanical Alignment

Watch this part6:09
  1. Turn the printer on.
  2. Allow the carriage to sit on the capping station.
  3. Turn the printer off from the rear switch.
  4. Rotate the knob clockwise to raise the capping station.
  5. Align the capping station to the print head.
  6. Rotate the knob counterclockwise to lower it.
  7. Move the carriage left.
  8. Tighten the two right-side bolts.
  9. Remove the four access screws to reach hidden bolts.
  10. Tighten the remaining bolts.
  11. Reinstall the panel loosely.

Step 13 – Adjust Capping Station Tilt

Watch this part7:29
  1. Move the carriage back to the capping station.
  2. Adjust the four tilt screws until alignment is correct.
  3. Tighten all four tilt screws once alignment is confirmed.

Step 14 – Adjust Capping Station Height (Software)

  1. Turn the printer on.
  2. Open Hosonsoft.
  3. Click Advance.
  4. Enter password 111111.
  5. Go to the Ink Stack tab.
  6. Increase Ink Stack Height from 6000 to 18000.
  7. Click Confirm.
  8. Observe capping station movement.
  9. Reduce value to 15500.
  10. Click Confirm.
  11. Set Pump Ink Stack Height to the same value.
  12. Click Confirm.

Step 15 – Adjust Wiper Blade Height

Watch this part8:31
  1. Press Left Arrow once to detach the capping station.
  2. Press and hold Left Arrow to move carriage near the wiper blade.
  3. In Hosonsoft, locate Scraper Ink Stack Height.
  4. Increase value from 3700 to 10700.
  5. Click Confirm.
  6. Observe blade height.
  7. Reduce value to 8700.
  8. Click Confirm.
  9. Verify blade is not bending and blocks view into printer bed.

Step 16 – Save and Initialize

Watch this part9:42
  1. Go to File.
  2. Click Save.
  3. Go to Operation.
  4. Click Initialize.
  5. Perform a head cleaning.

Step 17 – Final Contact Verification

Watch this part10:23
  1. Observe capping station contact from front and side.
  2. Confirm even contact on both sides.
  3. Adjust tilt again if needed.

Step 18 – Final Reassembly

Watch this part11:07
  1. Secure cables with zip ties as originally routed.
  2. Reinstall rear panels.
  3. Secure rear panel with eight screws.
  4. Reinstall waste tank.
  5. Reinstall top cover and secure with screws.
  6. Reinstall side panel and secure with screws.
  7. Close the side door.

Completion

What you need

  • Capping station aligned correctly
  • Wiper blade height adjusted
  • Ink stack heights saved
  • Printer ready for operation

Stuck on a step?

Your authorized dealer installs, trains and services your machine, and our factory support team is behind them. Reach either from the support page.

Get support