Vega S17

Vega S17 Quick Start Guide

Every step links to its own moment in the videos, so you never hunt for the right part again.

  • 27 steps
  • 153 instructions
  • 6 videos
  • 6 chapters
  • Updated 2026-11-15

User manualPDF · 24.5 MB

1. Install the Ink

How to Install the Ink on the Vega S17

  1. 0:20Agitate the White Ink
  2. 1:04Install the Cartridges
  3. 1:37Power On
  4. 1:50Initial Ink Charge
  5. 2:30Leave It On
Written steps 5

Agitate the White Ink

Watch this part0:20
  1. The Vega S17 prompts you to agitate the white cartridges every 12 hours. When that message appears, take care of it before you continue printing.
  2. Remove each white cartridge.
  3. Wipe any dirt from the cartridge and its slot with a lint-free wipe.
  4. Check the cartridge for tears or cracks.
  5. Hold the cartridge with the ink supply port facing up.
  6. Tilt it side to side at a 45 degree angle for 50 seconds, at about two back-and-forth shakes per second.
  7. Do not shake the cartridge too fast, too hard or in a different direction.
  8. Wipe any ink from the supply port, then reinstall the cartridge.

Install the Cartridges

Watch this part1:04
  1. There are eight slots: W1 and W2 for white, CL1 and CL2 for cleaning fluid, then C, M, Y and K.
  2. Check each cartridge color before it goes in.
  3. Insert the two white ink cartridges and the two cleaning fluid cartridges. Each one can go in either of its two slots.
  4. Then install cyan, magenta, yellow and black.
  5. Do not touch the inside of the machine, and do not touch the ink inlets or chip contacts on the cartridges.
  1. Connect the power cord to the power connector on the back of the unit.
  2. Do the same for the finishing section.
  3. Turn both main power switches on.
  4. Hold the sub power button for more than two seconds.

Initial Ink Charge

Watch this part1:50
  1. After it boots, the Vega S17 starts the initial ink charge on its own. It takes about 20 minutes.
  2. While it charges, do not lift the top cover and do not pull out any cartridges.
  3. If you lift the cover, the charge pauses. Hold the sub power button to reboot, and it picks back up.
  4. When the charge is done, Ready shows in the upper left corner of the touch screen.
  5. Check the status light too. Green means the machine is good to go. Purple means it works, but there is a warning to check. Blue means it is busy printing or running maintenance. Red means an error.
  6. Fix red right away, because automatic maintenance stops while there is an error.

Leave It On

Watch this part2:30
  1. The Vega S17 runs its own maintenance. It circulates ink and cleans the heads on a schedule, but only while it is powered on.
  2. Keep it on. If it is off for 12 hours or more, the heads may clog.
  3. If it ever has to be off longer than that, it needs to be flushed with storage fluid first.

2. Load the Film

How to Load Film on the Vega S17

  1. 0:17Prepare the Roll
  2. 0:39Load the Media Shaft
  3. 1:09Feed and Align the Film
  4. 1:33Complete the Media Setup
Written steps 4

Prepare the Roll

Watch this part0:17
  1. Check the leading edge of the film.
  2. If it is damaged, wrinkled, folded, curled, dented, torn or loose, or has tape or adhesive on it, cut it back to a clean, straight edge before loading.

Load the Media Shaft

Watch this part0:39
  1. Lift the green latch to release the media shaft from the machine.
  2. Remove the side bracket from the shaft.
  3. Slide the new film roll onto the shaft.
  4. Bring both side brackets flush to the roll.
  5. Tighten the side brackets and lock the lever, so the roll cannot shift side to side.
  6. Reinstall the shaft. Position it so its right edge is covered by the black shutter shown in the user manual.
  7. Keep your fingers away from the gear side of the spool and from the cutter area.

Feed and Align the Film

Watch this part1:09
  1. Release both pinch roller levers.
  2. Feed the film into the machine in the correct winding direction, and guide it forward to the printout position.
  3. Use the red marker to adjust the film until the input side and the output side are balanced.
  4. The film should track straight, with no sagging or wrinkles.
  5. Lower both pinch roller levers to secure the film.

Complete the Media Setup

Watch this part1:33
  1. On the touch panel, open the status window and press Media Setup.
  2. Let the machine complete the media set action.
  3. Check the film across the full printing area one more time. It must be flat, straight and free of sag before you print.
  4. If the film is not flat, stop and correct the loading and tension. Do not start a print with raised or wrinkled film.
  5. You can monitor how much film is left on the roll with the green dots on the touch panel.

3. Print

How to Print on the Vega S17

  1. 0:16Final Check and Start
  2. 0:36Monitor the Print
  3. 1:03Pause or Cancel a Job
  4. 1:20Finish the Job
Written steps 4

Final Check and Start

Watch this part0:16
  1. Confirm the touch panel shows Ready or Warning.
  2. Confirm the correct job is in the preview and the copy count is correct.
  3. Confirm the film is flat.
  4. If Warning is displayed, review the status window and make sure the warning does not require action before printing.
  5. Press Print to start the job.

Monitor the Print

Watch this part0:36
  1. Follow the total job progress and the current copy progress on the touch panel.
  2. Watch the film path and the output area. The film should stay flat and track straight through the system.
  3. Keep hands, tools, garments and loose material away from the moving film, the cutter and the output path.
  4. If an error or an abnormal film condition appears, press Stop and follow the approved troubleshooting procedure before continuing.

Pause or Cancel a Job

Watch this part1:03
  1. To pause the current operation, press Print during printing.
  2. Resume only after the issue has been checked and the film path is clear.
  3. To end the current job, press Stop, then Cancel, and confirm the cancellation on screen.

Finish the Job

Watch this part1:20
  1. Let the final sheet move through the finishing section and into the integrated stacker.
  2. Wait until the cut is complete and machine movement has stopped before reaching into the output area.
  3. Remove the completed sheets from the stacker. Keep the printed surfaces clean.
  4. Check the touch panel for a completion message, warning or error. Address any warning before the next job.
  5. Leave the Vega S17 powered on after production, so its automatic maintenance and ink stability routines can continue.

4. Daily Maintenance

Vega S17 Daily Maintenance

  1. 0:25Protect Automatic Maintenance
  2. 1:02Agitate the White Cartridges
  3. 1:46Run a Nozzle Check
  4. 2:16Recover a Nozzle Problem
Written steps 4

Protect Automatic Maintenance

Watch this part0:25
  1. Before you begin, put on polyethylene gloves and protective glasses. You will also need lint-free wipes and genuine DTF film.
  2. Leave the Vega S17 powered on.
  3. While it is on, it circulates the white ink every hour, cleans the white channels every three hours, and runs an all-channel clean every 12 hours.
  4. Automatic maintenance stops if the machine is off, a cartridge is missing or empty, the waste bottle is full, the top cover is open, or an error or service call message is active.
  5. Before you start, confirm that every cartridge has more than 5% remaining, the waste bottle has room, the top cover is closed and there is no active error.

Agitate the White Cartridges

Watch this part1:02
  1. The Vega S17 prompts you to agitate the white cartridges every 12 hours. When that message appears, take care of it before you continue printing.
  2. Remove each white cartridge.
  3. Wipe any dirt from the cartridge and its slot with a lint-free wipe.
  4. Check the cartridge for tears or cracks.
  5. Hold the cartridge with the ink supply port facing up.
  6. Tilt it side to side at a 45 degree angle for 50 seconds, at about two back-and-forth shakes per second.
  7. Do not shake the cartridge too fast, too hard or in a different direction.
  8. Wipe any ink from the supply port, then reinstall the cartridge.

Run a Nozzle Check

Watch this part1:46
  1. Run a nozzle check before each job. Load genuine DTF film.
  2. On the touch panel, press Maintenance, then Nozzle Check. Select white and color, and press Select.
  3. Inspect the printed pattern. A good pattern has complete, even horizontal lines.
  4. Uneven lines show deflection. Small gaps show clogged nozzles.
  5. If the pattern is clean, your daily maintenance is complete and you can begin printing.

Recover a Nozzle Problem

Watch this part2:16
  1. If the pattern has a problem, note the head number shown with that pattern.
  2. Press Maintenance, then Auto Head Clean.
  3. Select only the affected head, or select all heads if needed.
  4. Use Normal for small or minor gaps. Use Strong only for large missing areas, or when Normal does not recover the pattern.
  5. Press Cleaning.
  6. When it finishes, print another nozzle check and confirm that the pattern has recovered.
  7. If Normal does not clear the issue, stop and follow the approved escalation procedure from DTF Station Technical Support. Do not repeat Strong cleaning without their direction.

5. Weekly Maintenance

Vega S17 Weekly Maintenance

  1. 0:34Enter Regular Maintenance
  2. 0:49Clean the Maintenance Unit
  3. 1:44Clean the Media Guide and Left Ink Sump
  4. 2:03Clean the Nozzle Cover
  5. 3:11Finish the Routine
Written steps 5

Enter Regular Maintenance

Watch this part0:34
  1. The Vega S17 prompts you to do this routine every seven days. If it runs 30 hours or more per week, do it weekly even if the prompt has not appeared yet.
  2. You will need polyethylene gloves, protective glasses, cleaning liquid, a dropper and dry cleaning applicators.
  3. On the touch panel, press Maintenance, then Regular Maintenance. The carriage moves to the center.
  4. Do not move the carriage by hand unless a step specifically tells you to.
  5. Open the top cover.

Clean the Maintenance Unit

Watch this part0:49
  1. Lightly dampen a cleaning applicator with cleaning liquid.
  2. Start with the wiper cleaner frame. Gently wipe its top, sides and inner surfaces with the dampened applicator.
  3. Then gently clean the wiper cleaner surface and the inside area.
  4. The wiper cleaner lever is thin. Do not bend or break it, and do not push the applicator in too deep.
  5. Clean the front, back and top edge of the wiper.
  6. Rotate the roller while moving the applicator back and forth, until the full circumference is clean.
  7. Clean the suction cap the same way. Take extra care around the insert inside the cap: do not shift or remove it.
  8. Lastly, clean the moisturizing caps. Do not deform or scratch them.
  9. Remove solidified ink from the cap rims without pressing hard.
  10. If cleaning liquid remains, remove it with a dry applicator.

Clean the Media Guide and Left Ink Sump

Watch this part1:44
  1. Gently wipe ink buildup from the media guide with a cleaning applicator and cleaning liquid. Do not press hard.
  2. Clean ink from the top and inside of the left ink sump. Do not leave wet ink on top of the sump.
  3. Repeat for all ink sumps.

Clean the Nozzle Cover

Watch this part2:03
  1. Open the back hatch to access the sumps.
  2. Remove the left sump screw and lift the sump out, to reach the nozzle cover area.
  3. Wipe only the nozzle cover surface, in the direction shown in the user manual. Do not touch the nozzle face.
  4. Keep the sides, the screw hole area and the leaf spring area dry. If a side surface needs cleaning, use a dry applicator only.
  5. Remove all remaining cleaning liquid with a dry applicator. Do not leave the head wet.
  6. Clean the left and right ribs at both ends of the carriage.
  7. Reinstall the sump. Line it up in the correct direction, using the divots in the Vega S17 for reference.
  8. Make sure the right side tab is fully engaged in the frame latch, then reinstall the screw.
  9. Move the printhead over the sump to check that the sump is installed correctly. The printhead should move smoothly. If it does not, reinstall the sump.
  10. A misaligned sump can damage the printhead later.

Finish the Routine

Watch this part3:11
  1. Close the top cover and press Yes. The carriage returns to the right and the head is capped.
  2. Run Auto Head Clean.
  3. Print a nozzle check and confirm normal ink discharge.

6. As-Needed Maintenance

Vega S17 As-Needed Maintenance

  1. 0:24Recover a Nozzle Problem
  2. 1:16Empty the Waste Ink Bottle
  3. 1:38Clean a Removed Cartridge and Its Slot
  4. 2:16Service the Guide Rods
  5. 3:32Finishing Section Service Intervals
Written steps 5

Recover a Nozzle Problem

Watch this part0:24
  1. Before any ink or cleaning work, put on polyethylene gloves and protective glasses.
  2. Inspect the printed nozzle check pattern. A good pattern has complete, even horizontal lines.
  3. Uneven lines show deflection. Small gaps show clogged nozzles.
  4. If the pattern has a problem, note the head number shown with that pattern.
  5. Press Maintenance, then Auto Head Clean.
  6. Select only the affected head, or select all heads if needed.
  7. Use Normal for small or minor gaps. Use Strong only for large missing areas, or when Normal does not recover the pattern.
  8. Press Cleaning.
  9. When it finishes, print another nozzle check and confirm that the pattern has recovered.
  10. If Normal does not clear the issue, stop and follow the approved escalation procedure from DTF Station Technical Support. Do not repeat Strong cleaning without their direction.

Empty the Waste Ink Bottle

Watch this part1:16
  1. When the waste ink message appears, stop and empty the bottle.
  2. Keep the bottle upright, and clean any ink lumps from the end of the waste tube.
  3. Reinstall the empty bottle.
  4. On the status screen, press Waste Ink Reset, only after the bottle is empty.

Clean a Removed Cartridge and Its Slot

Watch this part1:38
  1. Every time you remove a cartridge, for replacement or for white ink agitation, inspect the cartridge and its slot for ink or cleaning solution residue.
  2. Use lint-free wipes only. Do not use cleaning liquid near the cartridge slot circuit board.
  3. Wipe the cartridge supply port and any residue on the cartridge body. Do not touch or stain the circuit board.
  4. At the cartridge slot, clean only the surface around the needle cylinder. Do not push the white resin part inward, and do not touch the circuit board.
  5. Reinstall the cartridge and confirm that the Vega S17 identifies it correctly.

Service the Guide Rods

Watch this part2:16
  1. How often depends on use. The user manual allows monthly service for lighter use. Machines in heavier use, such as five days a week for seven to eight hours a day, need more frequent service.
  2. On the touch panel, press Maintenance, then Regular Maintenance.
  3. When the carriage moves to the center, open the top cover.
  4. Keep hands and tools away from the encoder strip, the carriage belt, the nozzle face and the maintenance unit area.
  5. Wipe old grease and lint from both guide rods.
  6. Move the carriage only within the safe sliding range, to expose the covered sections of the rods.
  7. With a new applicator, apply the dedicated grease at the locations shown in the user manual.
  8. Spread the grease smoothly across the top third of each rod.
  9. Move the carriage slowly left and right within the safe range, for at least two round trips, to distribute the grease.
  10. Remove any grease outside the specified coverage. Make sure no grease reaches the filler sensor.
  11. Move the carriage to the left end, close the top cover and press Yes. The carriage returns home and the head is capped.
  12. Run Auto Head Clean. Then print a nozzle check and confirm normal ink discharge.

Finishing Section Service Intervals

Watch this part3:32
  1. Behind the front door of the Vega S17 is a panel. Unlock the panel to access and replace the filters.
  2. Replace the HEPA and carbon filters every 3 months.
  3. Replace the medium filter every 6 months.
  4. Replace the de-mist filter every 9 months.

Stuck on a step?

Your authorized dealer installs, trains and services your machine, and our factory support team is behind them. Reach either from the support page.

Get support